490-01REMINGTON482-1REMINGTON®POWDER ACTUATED TOOLMANUFACTURERS´ INSTITUTE INC.™G 029®ANINDEPENDENTLABORATORYTESTINGFORPUBLICSAFETYG 028PowerdriverMod
POWDERLOADS482-56Safety Precautions82. Remington Powder Loads are available in four power levels with gray (1) beingthe lowest power level and yellow
482-59Safety Precautions97. NEVER use common nails or other materials as fasteners. Remington PowerFasteners are manufactured from special steel and h
Why A Power Fastener Holds10WHY A POWER FASTENER HOLDSIN CONCRETEThe compression bond of the concrete to the powerfastener accounts for the majority o
482-85Wood or Non-Metals To Concrete482-66RIGHT482-79Wood or Non-Metals To Steel482-67OVERDRIVESelecting Power Fastenersand Powder LoadsFASTENING INTO
482-7112Operation1. Grasp muzzle and slide barrel forward rapidly until it stops. This sets piston intofiring position and opens the chamber.4. Push b
489-40Operation1330489-WATER489-33489489-415. Place the muzzle of tool perpendicular to work surface without tilting the tool.Push tool against work s
490-03123456789101112131416151718192014Key Part No. Part No.No. 489 490 Description Qty.1 TA4000 TA4000 BARREL, Assembly and Piston 12 076659 076659 B
489-4715Barrel ReplacementREMINGTON489-51AD489-50FA489-48B489-46EREMINGTON489-45DREMINGTON489-43A4. Insert screw (A) and tighten. Insert and tighten p
16ABCDEFGHIJKLMNOPQRSTUV490-04
Tool DisassemblyAnd Assembly17TOOL DISASSEMBLY1. Remove screw (G) from recoil pad (H). Lift pad away from handle. Separatehousing halves by removing t
INDEXWarning: Safety Precautions ... 1-9Why A Fastener Holds ...
Piston hangs outof muzzle.PROBLEMPiston jammed.Overdriven fastener.Reduction or lossof power.Tool does notcompletely depress.Tool does not fire.Expend
Troubleshooting Guide (cont.)19Dirt build-up on breech notallowing proper penetrationof firing pin.Check firing pin indentationon cartridge. Clean bre
Two by foursFurring stripsElectricaljunction boxesConduit clipsShelf brackets1/4" Plywood orpegboardFor fastening this20Application Chart482-81a2
21Application ChartLoad Color CodeStock Level Load CaseNumber Number Strength Body HeadA22C1 1 light brass GrayA22C2 2 medium brass BrownA22C3 3 he
Limited Warranty AgreementFor Technical Assistance or Repair on YourRemington Powder Actuated Tool, CallTechnical Services Department1-800-323-5190For
489-08489-07489DEFECTIVE489-06?489-04?489-03BEFORE USING1. ALWAYS handle the tool as if it were loaded. Before starting work, check thatthe tool is un
5. ALWAYS make sure the work area is clean from loose material and debris.Safety Precautions1. NEVER place your hand over the muzzle. Accidental disch
Safety Precautions3489-15489-174. NEVER carry or pass a loaded powder actuated tool. NEVER point a powderactuated tool at anyone.3. ALWAYS store UNLOA
Safety Precautions4G 018G 018TOO HARDPointflattens482-29????482-26???7. An operator taking medication should take extra precautions while handling the
489-28489-26489-25Safety Precautions5G 018G 018G 018G 0183. NEVER make fastenings in spalled or cracked areas.2. NEVER attempt to drive power fastener
Safety Precautions6YES7. DO NOT drive power fasteners into steel base material less then 3/16" thick,within 2" of a weld, within 1/2" o
Safety Precautions7489-34WATER489-3330489-GASOLINEGASOLINE482-50POWDERLOADS3. ALWAYS use the spall shield when driving directly into concrete or steel
Commentaires sur ces manuels