Remington BS188A Manuel du propriétaire télécharger pdf (Page 15)

POLESAW INFORMATION

POLESAW ASSEMBLY

_k WARNING: Cutting edges on

chain are sharp. Use protective

gloves when handling chain.

I.

2.

Remove battery from chain saw.

Separate main handle from chain saw

power head by pressing both release

buttons on main handle and pulling

apart (see Figure 21).

Press

Release Release

Button

Buttons

Figure 21 - Separate Main Handle from

Powerhead.

3. Align rib on chain saw power head with

groove in power head adapter on pole

(see Figure 22).

Groove

Power Head "

,,

Polesaw

Power Head

Adapter

Figure 22 =Align Power Head with Power

Head Adapter

4.

Slide power head into power head

adapter until units "snap" together (see

Figure 23). IMPORTANT" Both release

buttons on power head adapter must be

fully engaged.

Figure 23 - Assembled Power Head and

Power Head Adapter

5. Align rib on handle adapter on pole

with groove in main handle (see Figure

24).

Groove

/

/

/

Rib/_

\\\\\

Polesaw \,

Handle"-\

Adapter

Main Hdhdle

Figure 24 =Align Main Handle wfh Ham

die Adapter

6. Slide main handle into handle adapter

until units "snap" together (see Figure

25). IMPORTANT: Both release but-

tons on main handle must be fully

engaged.

Figure 25 - Assembled Main Handle and

Handle Adapter

7. Slide battery onto main handle until

release buttons "snap" together (see

Figure 26).

Note: Fully charge battery beti)re using

tk)r first time. See Charging Battery,

page 10

Figure 26 - Assembled Battery onto Main

Handle

ADJUSTING POLE LENGTH

The Remington brand polesaw has a tele-

scoping pole assembly that will extend from

47 inches (fully retracted) to 83 inches (fully

extended). A cam levered collet is used to

hold the pole in position at any extended

length.

1. To extend the pole, loosen the clamping

lever (see Figure 27). Pole will slide

freely.

2. Pull inner pole section out to desired

length of extension. Note: Only extend

pole to minimum length required to

reach limb that is being cut.

3. To lock pole in position, tighten clamping

lever (see Figure 27).

UNLOCK LOCK

Figure 27 - Extending TelescopicPole

CUTTING WITH THE POLESAW

I. Attach battery to saw.

2. Use both hands to grip polesaw. Use

only designated grip areas when oper-

ating polesaw (see Figure 28). Use firm

grip. Thumbs and fingers must wrap

around polesaw handle and pole.

3. Make sure your ti_ofing is firm. Keep

feet apart. Divide your weight evenly

on both feet.

f

Figure 28= Designated Grip Areas

4. When ready to make a cut, press in

trigger lockout and squeeze trigger (see

Figure 29). This will turn polesaw on.

Releasing trigger will turn polesaw off.

Make sure saw is running beti_re starting

a cut.

5. When starting a cut, place moving

chain against wood. Hold polesaw

firmly in place to avoid possible bounc-

ing or skating (sideways movement) of

saw.

6. Guide polesaw using light pressure. Do

not ti_rce saw. The motor will overload

and can burn out. It will do the job bet-

ter and safer at the rate for which it was

intended.

7. Remove polesaw from a cut with saw

running, at full speed. Stop polesaw by

releasing trigger. Make sure chain has

stopped before setting polesaw down.

Trigger

Trigger Lockout

Figure 29- Polesaw Handle with Trigger

Lockout

15 www. remingtonpowertoo/s, com

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 46 47

Commentaires sur ces manuels

Pas de commentaire